MACHINED PARTS SHIP IN 3 DAYS, ORDER YOUR METAL & PLASTIC PARTS TODAY.

Table of Contents

Home - Blogs - CNC Machining - How Does Wire EDM Work, and When Does a Part Need It?

How Does Wire EDM Work, and When Does a Part Need It?

Consider two features on a tool plate. One is a narrow slot that goes all the way through the plate. The other has the same outline on the top view but stops above the bottom face. A section view can decide which process to quote. The through-slot may suit wire electrical discharge machining (wire EDM), while the blind pocket needs a different route.

What cuts the material?

A wire EDM machine feeds a thin, electrically conductive wire between guides. A pulse generator creates discharges across the small gap between wire and workpiece. Each discharge removes a little material. A dielectric fluid, commonly deionized water, supports the process and helps carry debris away. The wire follows a programmed path without pressing a cutting edge into the stock.

The workpiece must conduct electricity. Hardness alone does not rule out the process, which is one reason it is considered for profiles in hardened tool steel. The wire needs a path through the stock. For an enclosed profile, it normally threads through a suitable start hole. A profile open to the edge can be approached from outside. A blind cavity with an intact floor leaves no exit for the wire.

Check the section view before you request a quote

Mark the material condition, stock thickness and surfaces that establish the part location. Then examine the corners, entry and exit faces together. A wire of finite diameter, plus the discharge gap, leaves a finite internal radius. A CAD model showing a mathematically sharp corner needs a physically acceptable radius or an agreed relief feature.

Drawing featureDecision to make before quoting
Enclosed through-profile in a conductive plateShow the contour and thickness. Confirm whether a start hole already exists or the supplier should include it.
Blind pocket with a floorReview milling or sinker EDM according to shape and access.
A tapered slot or different contours at each faceProvide both profiles or a section. Ask the supplier to confirm guide travel, taper and inspection access.
Several surfaces with different finish requirementsIdentify which faces need a finish or profile report and where additional passes are justified.

What changes the quoted work?

Start-hole preparation, length of cut, thickness, tolerances and the requested surface condition all affect the process plan. A rough cut creates the basic profile. Additional skim cuts can refine the size and surface. Their number depends on the part and the acceptance criteria. The supplier also has to control or remove the piece released by an internal cut.

For a critical profile, identify the datum features used for inspection and whether the requirement applies at both faces or through the thickness. If the specification restricts the surface layer altered by electrical discharge, include the relevant requirement and any test or subsequent finishing operation. A visual check alone cannot verify a metallurgical requirement.

Example quote request

“Please quote the enclosed through-profile in the hardened tool-steel plate shown in the drawing. The solid model and section A–A identify the minimum corner radius and plate thickness. Include the start hole in your scope. Report the profile relative to the marked datums on the first part. Flag any corner or access condition that needs a drawing change.” A section and a datum scheme give the supplier more to work with than a top-view outline alone.

How wire EDM defines a tapered gauge opening

A top view alone leaves the bottom opening ambiguous. Show the upper and lower profiles in the same viewing direction, locate both from the same datums, and give the distance between their planes.

Identify which edges the gauge must pass at each face. Ask the shop to confirm that its wire tilt and available clearance can produce both profiles before releasing the drawing.

Related materials and services

Technical references

Group of consumer electronic devices
Patrick

Hey there, I’m here to help you with all your machining needs. Get in touch for a quote on your ongoing or upcoming projects!

Connect with CNC Machining Services

Partner with Us for Custom CNC Parts

We provide fast, reliable delivery of CNC-machined parts. Upload your design files to get a quote and begin production immediately.

We support both prototyping and production, ensuring that every part meets your specifications and is delivered on time.

Get In Touch

Related Articles and Insights

Stay updated with the latest insights, industry trends, and expert tips on CNC machining and precision manufacturing. Explore innovative solutions and learn more about the advancements shaping the future of machining.
Get In Touch