MACHINED PARTS SHIP IN 3 DAYS, ORDER YOUR METAL & PLASTIC PARTS TODAY.

Table of Contents

Home - Blogs - CNC Machining - 6061-T6 vs. 7075 Aluminum for CNC Machined Parts

6061-T6 vs. 7075 Aluminum for CNC Machined Parts

A bracket that bends under load and a bracket that springs back but deflects too far have different design problems. Before changing the alloy on either drawing, establish what limits the part. Strength, stiffness, corrosion exposure and any welding after machining each point to a different question for the engineer and the supplier.

Start with the failure mode

6061-T6 is a practical starting point for a machined housing, fixture or bracket when its design meets the load requirement. It offers good corrosion resistance and is commonly selected where welding is required. A weld can change the local properties of a heat-treated part. An assembly that relies on the T6 strength of the original plate needs its welded condition reviewed separately.

7075 in a T6-family temper has higher yield strength than 6061-T6. For a compact, bolted component that takes a high load, that can make 7075 worth evaluating. The two alloys have broadly similar elastic moduli. With the same geometry and a load within the elastic range, switching alloys alone usually brings little improvement in deflection. Look at section depth, rib placement and support distance if stiffness is the limiting requirement.

Use the drawing to narrow the choice

A quotation should identify which requirement drove the material choice. These are starting points for a review. The design authority selects a material specification and verifies the part in its service environment.

What the part requiresWhat to review
A welded frame with machined interfacesEvaluate 6061 and the weld procedure. Define whether critical faces are machined before or after welding.
A highly loaded bracket with limited spaceCompare 7075 and 6061 against the required load, fatigue duty and allowable section size.
An exterior part exposed to moisture or saltsSpecify exposure, finish and inspection. Check the selected alloy and temper for the actual environment.
A cover that must stay flat under loadReview geometry, supports and assembly loads. Verify stiffness with the chosen material and shape.

Specify product form, condition and finish

A drawing that says only “7075 aluminum” leaves the temper open. Name the approved alloy, temper, product form and governing specification. Distinguish T6 from stress-relieved conditions such as T651 when the drawing requires a particular condition. A plate data sheet and a bar data sheet can have different limits. Use the values for the stock form and thickness actually being purchased. Typical values from an alloy brochure are useful for screening. Design allowables and acceptance limits belong to the applicable specification.

If the part will be anodized, indicate the faces to mask and whether a critical dimension applies before or after coating. Include a named cosmetic reference if color matters. For a thin pocketed housing, identify the flatness-critical face and how the part is supported during inspection.

Example quote request

“Please quote the attached sensor bracket in the specified 6061-T6 plate, for 5 prototypes and a repeat lot of 50. The two mating bores are dimensioned after finishing. Mask the marked faces. Provide a material certificate. If you propose 7075, quote it separately and identify the temper.” This gives purchasing a comparable base quote and leaves any material change with the design owner.

Which value belongs on the purchase drawing?

When comparing 6061-T6 and 7075 for a bracket, check the heading above each property in the supplier’s data sheet. A typical value can help screen an alloy, but it does not establish the minimum the purchased stock must meet.

If a minimum property drives the choice, give the applicable material specification, temper and stock form on the order. Ask what document will demonstrate compliance for the supplied lot.

Related materials and services

Technical references

Group of consumer electronic devices
Patrick

Hey there, I’m here to help you with all your machining needs. Get in touch for a quote on your ongoing or upcoming projects!

Connect with CNC Machining Services

Partner with Us for Custom CNC Parts

We provide fast, reliable delivery of CNC-machined parts. Upload your design files to get a quote and begin production immediately.

We support both prototyping and production, ensuring that every part meets your specifications and is delivered on time.

Get In Touch

Related Articles and Insights

Stay updated with the latest insights, industry trends, and expert tips on CNC machining and precision manufacturing. Explore innovative solutions and learn more about the advancements shaping the future of machining.
Get In Touch